plastic exterior wall sheathing requirements

Attaching Exterior Wall Cladding Through Foam Plastic Insulating .

So, more exterior rigid foam wall sheathing. Sheathing has thicknesses up to 4 inches to be an effective insulator. Insulation enables us to meet or exceed modem energy code requirements. Therefore, the focus here is helping meet LEED, Energy Star (EPA), and the ICC 700 National Green Building Standards. Attaching..

Continuous Insulation for Code-Compliant, High . - RCI, Inc.

Jan 3, 2012 . structural systems and cladding materials such as cement board, PC stucco, wood lap, brick veneer, stone, and vinyl siding. Furthermore, CI can be placed on the inte rior or exterior side of the wall with proper consideration of climate-dependent mois ture vapor control code requirements. For example, it is..

Foam Sheathing Coalition - National Gypsum Company

is adequate to resist code-required design wind loads to prevent pull-off of the exterior wall covering assembly (i.e., cladding and siding as well as the foam sheathing). Table 1a Siding Minimum Fastening Requirements for Direct Cladding Attachment over Foam. Plastic Sheathing to Support Cladding System Weight

Exterior Wall Coverings | Home Owners Network

You need not install water-resistive materials: (a) over concrete and masonry walls that are built and flashed according to the requirements in Chapters 6 and 7, and (b) at . The Class III vapor retarder exceptions refer to using ventilated exterior wall cladding (such as brick, aluminum siding, and vinyl siding) and using high..

Residential - Walls |

Requirements for installation of vinyl siding over foam sheathing in thicknesses up to 4" when used as thermal insulation in exterior walls. Available as sealed code compliance report. Attachment of Exterior Wall Coverings Through Foam Plastic Insulating Sheathing (FPIS) to Wood Wall Framing Report. Cladding installation..


EXTERIOR WALLS. SECTION 1401. GENERAL. 1401.1 Scope. The provisions of this chapter shall establish the minimum requirements for exterior walls; exterior . as adding strength to the wall. VINYL SIDING. A shaped material, made principally from rigid polyvinyl chloride (PVC), that is used as an exterior wall covering

Nail-Base Sheathing - APA The Engineered Wood Association

Easy Siding & Trim Attachment. Meet code requirements and simplify fastening of siding and trim to plywood or OSB. Continuously sheathing with OSB or plywood not only makes walls stronger and more resilientthese structural panels also make a solid, consistent surface for attaching siding and trim that meets the..

FLOODING: Vapor Barriers and Mold - Paul's House

Sep 1, 2016 . Unfortunately, we only recently noticed, more than two weeks later, that we did not think to remove the vapor barrier strip located on the inside base of all exterior walls. (Just so we are on the same page, the vapor barrier I am referring to is a strip of plastic located between the studs and the plywood used to..

CommercialComplete Wall Systems Architectural . - Owens Corning

Owens Corning's CommercialComplete Wall Systems are a variety of exterior wall system solutions that . a layer of continuous insulation (ci) to thermally seal the exterior wall and minimize ... AC 71, Acceptance Criteria for Foam Plastic Sheathing Panels Used as Water Resistive Barriers, International Code Council

exterior walls - Florida Building Commission

Feb 1, 2002 . Vinyl siding shall be secured to the building so as to provide weather protection for the exterior walls of the building. 1405.13.1 Application. The siding shall be applied over sheathing or materials listed in Section 2304.6. Siding shall be applied to conform with the water-resistive barrier requirements in..

APA Engineered Wood Construction Guide

Walls are a critical structural component in any structure. Building codes require that walls resist wind pressures and wall-racking forces and provide weather protection. Builders and designers can choose from a variety of wall sheathing products and wall systems. This section provides an overview of several commonly..

Attachment of Exterior Wall Coverings Through FPIS | DrJ Best .

Foam Plastic Insulating Sheathing (FPIS) Products are offered in three types: Expanded Polystyrene (EPS) - ASTM C578; Extruded . Exterior wall coverings are attached directly through the FPIS into the framing or to furring attached through the FPIS to framing. Shall be installed in accordance with: DRR No. 1303-04..

Attaching Exterior Wall Coverings through Foam Sheathing to Wood

Dec 21, 2017 . 1.1. Attachment of exterior wall coverings through Foam Plastic Insulating. Sheathing (FPIS) to wood wall framing. 1.2. For the most recent version of this report, visit For more detailed state professional engineering and code compliance legal requirements and references, visit..

SECTION 6 Preparing for Horizontal Siding - CertainTeed

Technical Bulletin: Attaching Exterior Wall Covering Assemblies with Foam Sheathing to Steel Wall Framing. The Fasten Master reports must be used in combination with. ICC-ES Evaluation Report ESR-1066 for vinyl siding or ICC-ES. Evaluation Report ESR-3085 for polymer shakes to determine attachment requirements

Sheathing: Mind the Gap, Eh! | Building Science Corp

Nov 15, 2013 . With foam sheathing (of the appropriate thickness R-value based on condensation control as noted above) the type of cavity insulation becomes irrelevant. Fiberglass batts .. Think interior plastic vapor barriers or vinyl wall coverings and exterior OSB sheathings or foil faced foam sheathings. Heck, all we..

CHAPTER 14 EXTERIOR WALLS | 2015 International Building .

The provisions of this chapter shall establish the minimum requirements for exterior walls; exterior wall coverings; exterior wall openings; exterior windows and doors; architectural trim; . Vinyl siding shall be certified and labeled as conforming to the requirements of ASTM D3679 by an approved quality control agency

Continuous Insulation Cladding/Furring Attachment - Code .

For guidance regarding cladding attachment over foam sheathing to masonry or concrete wall construction refer to the 2015 IRC, Section R703.17. Plan Review: Per the 2015 .. Table R703.15.1. Cladding Minimum Fastening Requirements for Direct Application over Foam Plastic Sheathing to Support Cladding Weight1..

Wall Sheathing Options |

Nov 20, 2015 . meet code requirements;; be affordable;; be strong enough to brace a wall (provide racking resistance);; hold nails and screws well without being so .. Builders who install a continuous layer of rigid foam insulation on the exterior side of their walls often install the foam over OSB or plywood sheathing

Exterior Wall Sheathing | UpCodes

Explore a searchable database of US construction and building code. Code regulations are consolidated by state and city for easier navigation