plastic sheathing for wood

CHAPTER 14 EXTERIOR WALLS | 2017 Florida Building Code .

Wood siding of thicknesses less than 0.5 inch shall be placed over sheathing that conforms to Section 2304.6. . Only Class III vapor retarders shall be used on the interior side of frame walls where foam plastic insulating sheathing with a perm rating of less than 1 is applied in accordance with Table 1405.3.2 on the exterior..

Details for Conventional Wood Frame Construction

ered as needed. Follow these simple rules: (1) Support framing lumber, plywood and panel prod- ucts at least six inches above ground and protect them below and above with a waterproof cover such as plastic film. Finish lumber and flooring, particu- larly, are to be protected from ground or concrete slab moisture and kept..

FAQs -- After Gutting a Flooded Home - LSU AgCenter

Nov 7, 2017 . A wet slab can lead to flooring failure and rewetting of wood framing. To monitor slab wetness, use a pinless moisture sensor, if possible. Otherwise, as a rough DIY indicator, tape an 18 inch square piece of clear plastic sheeting on the concrete. Monitor for 24 hours, then if visible moisture collects under the..

Foam Sheathing Coalition - National Gypsum Company

Spacing. (inches). Maximum Thickness of Foam Plastic insulating. Wall Sheathing (inches). 16" o.c. Fastener Horizontal. Spacing. 24" o.c. Fastener Horizontal. Spacing. Max. Cladding Weight: Max. Cladding Weight: 3 psf. 11 psf. 25 psf. 3 psf. 11 psf. 25 psf. Wood Framing. (minimum. 1-1/4" penetration). 0.113" diameter nail

Moisture control techniques for wood-framed homes | Professional .

A water-resistive barrier (WRB) is commonly used to protect the outer surface of wood sheathing from any rain water that penetrates past the cladding. .. When fastening the housewrap to the sheathing, space evenly every 12 to 18 inches and use plastic cap nails or staples to minimize the chance of the fastener pulling..

Sheathing - Buildipedia

Jul 27, 2009 . Commonly called sub-flooring, structural panels are engineered wood products known as plywood and oriented strand board (OSB). Plywood is made from thin sheets of veneer that . Types include plastic, foam, cellulose fiber, paper faced and foil faced boards. Insulating sheathing is a lightweight panel..

L&W Supply - Tampa Wood Panel Product Sheathing 061636 | AWCI

Division 060000 - Wood, Plastics and Composites. 061636 Wood Panel Product Sheathing. L&W Supply - Tampa. 2817 N 36th St Tampa, FL 33605 USA. Contact: Dan Hinkle, Branch Manager Phone: (813) 247-5402. Fax: (813) 247-4851. E-Mail: dhinkle@lwsupply.com. URL: www.lwsupply.com. Social Media:..

Is there code that states there must be a sheet of plastic between .

Yes. What he was talking about was the "water-resistive barrier." (WRB) This is typically Tyvek housewrap (a kind of vapor-permeable plastic) or grade D building paper (tar-soaked paper). All wood-framed buildings need one of these, or else any water that penetrates the siding can contact the sheathing,..

Vapor Barriers 101 | The Craftsman Blog

Mar 2, 2015 . Sure, there may have been felt paper or rosin paper installed under the hardwood floors or behind the siding, but these pieces weren't as much about vapor protection as they were about . Plastic sheeting, often called Visqueen, is the least permeable of all vapor barriers- having a rating of less than 0.1

Horizontal Stabilisation of Sheathed Timber Frame Structures Using .

Oct 18, 2016 . In this part 2, the practical design and strength of a number of different joints is described: (1) Sheathing-to-framing joints the plastic design method is

Woods, Plastics and Composites - Eastern Michigan University

Feb 18, 2008 . Division 06 Woods, Plastics and Composites. Page 06-2. Section 06 16 00. Sheathing. 1. While lumber species and grade may vary in availability or cost depending on seasons or market influences, minimum quality characteristics of structural lumber shall be as follows: a. Floor Sheathing: ¾ T&G Floor..

SECTION 06160 - SHEATHING MasterSpec - CertainTeed

Include data for wood-preservative treatment from chemical treatment manufacturer and certification by treating plant that treated plywood complies with requirements. Indicate type of preservative used and net amount of preservative retained. . Fire-retardant-treated plywood. Foam-plastic sheathing. Building wrap

Exterior Wall Sheathing | UpCodes

Where wood structural panel sheathing is used as the exposed finish on the outside of exterior walls, it shall have an exterior exposure durability classification. Where . or equivalent is installed on the side of the wall opposite the foam plastic sheathing, the minimum siding fastener penetration into wood framing shall

Alternatives to Drywall for Garage Walls | Home Guides | SF Gate

Jun 16, 2017 . These panels resist mold, pests, mildew and moisture, and are easy to clean if exposed to grease or other contaminants. Not all FRP and plastic panels can be installed directly to wall studs; most are designed to go over drywall or wood sheathing. Check the installation instructions to confirm whether your..

Comparison of Fire Performance Requirements of the IBC and IRC .

Foam Sheathing Coalition 1156 Fifteenth St NW Ste 900 Washington, DC 20005. 202/785-3232 202/223-9741 (fax) www.foamsheathing.org. T-Fire. Comparison of Fire Performance Requirements of the IBC and IRC for Wood Structural Panels and Foam Plastic Insulating Sheathing. Released October 22, 2010

R703.15 Cladding Attachment Over Foam Sheathing to Wood Framing

Cladding shall be specified and installed in accordance with Section R703, the cladding manufacturer's approved instructions, including any limitations for use over foam plastic sheathing, or an approved design. In addition, the cladding or furring attachments through foam sheathing to framing shall meet or exceed the..